KATL CHARTS PDF

N / W. Elevation, FT. Variation, 5 W . From city, 7 miles S of ATLANTA, GA. ARTCC, ZTL. Section chart, ATLANTA. Airport Charts[S] Z 06/26/14 – Z 07/24/14 d -TPP ยท AIRPORT DIAGRAM, TAKEOFF MINIMUMS, HOT SPOT. ATL (KATL), HARTSFIELD – JACKSON ATLANTA INTL, an airport/aviation facility HARTSFIELD – JACKSON ATLANTA INTL – Airport Diagram KATL VFR.

Author: Negul Kagasida
Country: Haiti
Language: English (Spanish)
Genre: Education
Published (Last): 5 January 2013
Pages: 17
PDF File Size: 20.71 Mb
ePub File Size: 10.87 Mb
ISBN: 190-2-96735-900-8
Downloads: 71776
Price: Free* [*Free Regsitration Required]
Uploader: Douzilkree

It is important to note that in many cases, ATC responsibility ends with the transition from taxiway to ramp. Runway markings are always white. Pilots anticipating movement at high-density airports should anticipate such instructions and be prepared to read them back, then follow them as instructed, especially during periods of heavy traffic.

Looking at the images above, the first shows the aircraft on Taxiway “Delta Two” denoted by the yellow numbers on a black field.

Black numbers on a yellow katp indicate directions to the runway s represented by the numbers. These can be found in chzrts various charting providers NOS, Jeppesen but are also largely available online.

Airport Diagrams

Touchdown zone elevation, lighting, and notes are included just as in the UK diagram, but presented differently. These are often referred to as “non-movement” areas. Runway Lighting Briefly in the image above you can see runway edge identifier lights that are white, turning to yellow as the departure end of the runway gets closer.

This diagram is smaller, more complex, and a bit more difficult to read. Again, as in the KATL case, you can see that the other runways are referred to as 26R and 26L, and the farthest south runway is Runways, Taxiways and Ramps: In the second, the aircraft is on a taxiway approaching a runway intersection. Most have yellow centerline markings to facilitate remaining in the center of, and following the taxiway in reduced visibility.

Briefly in the image above you can see runway edge identifier lights that are white, turning to yellow as the departure end of the runway gets closer.

In the upper right of the image you can see all blue taxiway lighting. Taxiways are designated surfaces provided at airports to enable aircraft to reposition from the runway to their final position on the field, or vice versa.

  ALEO S18 240 PDF

This segment will provide basic understanding of airport diagrams to enable pilots to navigate safely and correctly at various airfields. You can see from these identifiers that one end of the runway is always the “reciprocal” of the other, or ? By Tom Seeley Purpose: The centerline lighting, white until ‘ remaining, then alternating red and white, warning of the reduced length, and ultimately all red. On the other hand it should be noted that Jeppesen provides larger fold-out diagrams for many high-density airports as well as “low visibility taxi route” charts and these are much easier to read and interpret.

The solid and dashed black lines indicate a “hold short” location of a taxiway approaching a runway, where you must stop if the solid line is nearest you, or which you must cross if exiting a runway and the dashed lines are nearest you.

At the other end of taxiways are “Ramps” which are not really ramps at all, but different surfaces that denote where the taxiway ends and the terminal or gate area begins.

However these are only available charte subscription. Look between runways 27L and 27R at taxiways Kilo and Lima However despite these sometime subtle differences, either diagram will facilitate on-airport navigation.

The quality of diagrams varies throughout the world, with some providing a general overview of the airport and others more detailed. In this case, the solid lines of the hold short line are toward the aircraft, and it cannot proceed past this point unless a clearance to do so has been received. Taxiways and runways are represented only by their kxtl or numeric labels. The line of demarcation between taxiway and ramp is normally a broken single or double yellow line.

Skip to main content. The EGCC diagram has numerous “shadow boxes” with important information such as touchdown zone elevation TDZ and localizer frequencies, for example.

They have different marking from runways, and are always identified by letters, with numbers if vharts. The signs in the images above are the universal signs used to denote directions to taxiways and runways. You must join, but registration is free and the site is very thorough.

  ELEKTROTECHNIKA TEORETYCZNA BOLKOWSKI PDF

At major airports each airline may have its own “ramp control” and may have a tower-like facility to control movement on its ramp. A partial example from the fold-out for KATL is reproduced below the kahl diagram. The Atlanta-Hartsfield diagram is representative of most U.

The hold short lines indicate the aircraft has just departed the runway and should not stop until after crossing the hold short line fully.

You can see that this diagram is quite detailed and colorized. Taxiway markings are always yellow. Black letters on a yellow background are directions to kat, taxiway represented by the letter.

This designation doesn’t mean there is no movement, but that either the pilot or some other authority assumes responsibility, or both. The UK diagram shows these quite clearly, while the US diagram makes them a little more difficult kalt see. When more than three are present, the others are given numerical designators -close- to their geographical orientation.

It denotes taxiways via replicas of the taxiway markings you would see looking out the cockpit kqtl, yellow against a black background.

Airport Detail: KATL |

Runways are always designated and normally marked by a one or two number label, loosely associated with their compass bearing.

One significant difference is taxiway hold points: All of these diagrams, regardless of how colorful or easy to read, provide basic information for navigating around an airport, and supplemental information which is either critical or informational. Upon completion, the pilot should have a clear understanding of the elements of an airport diagram and how to use it. A RUNWAY is differentiated from other surfaces on the airport by being the only surface an aircraft other than a helicopter either lands on or takes off from.

Runways may also be used for taxiing aircraft and in some cases for parking aircraft. The portrayal of runway markings and orientation is also a faithful representation of the real-world airport.