ASTM A255 PDF

Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.

Author: Nanris Fauk
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Relationship
Published (Last): 24 June 2012
Pages: 187
PDF File Size: 5.56 Mb
ePub File Size: 8.19 Mb
ISBN: 594-8-28816-923-7
Downloads: 66937
Price: Free* [*Free Regsitration Required]
Uploader: Nakasa

In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level. Cast tests need not be normalized. If the retest also has greater than 4 HRC points spread, a new specimen should zstm tested.

Examples of this method are J 4?

ASTM A255 PDF DOWNLOAD

This testing can astm a done on a sub-sized sample which does not meet the standard size bar dimension as governed by Appendix X1. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The Certified Material Test Report shall state the method of hardenability determination.

Link to Active This link will always route to the current Active version of the astj. In cases of lack of reproducibility or of differences between laboratories, indenter spacing should be measured immediately. If such changes caused by grinding are indicated, new?

In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level. Last previous edition A — Grossman and asym increased accuracy by re? The use of these equations to plot curves may result in random in? Active view current version of standard. As the voice of the U. Link satm Active This link will always route to the current Active version of the standard. Need more than one copy?

  DATA STRUCTURES USING C YASHWANT KANETKAR PDF

The time between removal of the specimen from the furnace and the beginning of the quench should not be more than 5 s. A — 99 Determinin If the two probes on opposite sides differ by more than 4 HRC points at 2a55 one position, the test should be repeated on new?

For comparison of this test method to others, or for steel compositions outside the mentioned grades, the user should refer to other articles concerned with calculating hardenability.

Referenced Astm a purchase separately The documents listed below are referenced within awtm subject standard but are not provided as part of the standard. For this example with 0. Values below 20 HRC are not recorded because such values are not accurate. The water-supply line shall also be provided with a quick opening valve. If the specimen is not cold when removed from the?

The test consists of water quenching one end of a cylindrical test specimen 1. It is the responsibility of the user of this standard to establish appropriate safety astm a health practices and determine the applicability of regulatory limitations prior to use. For DI in millimetres, use the metric value table. Hardenability curves obtained from tests on these smaller specimens therefore are not comparable with curves obtained from tests on the standard 1.

The higher the carbon or alloy content, or both, the lower the boron factor. Users w255 this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Active view current version of standard. Carbon and Sulfur Analysis.

ASTM A – The Jominy End Quench Test of Hardenability

Plating and Coating Testing. Jominy Testing This testing is indented for determining the hardenability of steels.

This standard is not included in any packages. These curves give High and Low values which material should fall into. The sample is then brought back up to austenitizing temperature as specified for a25, and end quenched with a specialized holder for the end quench to occur. In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level.

  ABB UNITROL 1000 PDF

It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench. The support for the specimen shall be dry at the beginning of each test. In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level.

If the document is revised or amended, you will be notified by email. The test consists of water quenching one end of a cylindrical test specimen 1.

Historical Version s – view previous versions of standard Translated Version s: We have no amendments asmt corrections for this standard. The two test methods include the quantitative end-quench or Jominy Test and a method for calculating the hardenability of steel from the chemical composition based on the original work by M.

Aa255 second hardness traverse is made after turning the bar over.

It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench. It is astm a quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized astm a Shallower ground depths can affect reproducibility of results, and correlation with cooling rates in quenched bars.