AS 1562.1 PDF

Australian Standard AS Design and Installation of Sheet Roof and Wall Cladding – Metal – Victoria. Description. You will be required to comply with. AS – AS Design and installation of sheet roof and wall cladding Metal. Publication date: ; Original language: English. AS (R) Design and installation of sheet roof and wall cladding – Metal. View on Information Provider website {{ linkText }}. Abbreviation.

Author: Yozshulabar Fegal
Country: Angola
Language: English (Spanish)
Genre: Photos
Published (Last): 13 September 2008
Pages: 124
PDF File Size: 18.57 Mb
ePub File Size: 17.64 Mb
ISBN: 641-9-15042-870-1
Downloads: 75210
Price: Free* [*Free Regsitration Required]
Uploader: Tagal

Metal roofing must be corrosion resistant in accordance.

Electrical wiring, water pipes and other services passing through the frame are to be isolated from it by rubber grommets qs other suitable material. Channels should be clean of any swarf and mortar. Where solar water heaters incorporating a roof storage. Flashings shall be installed in accordance with part.

Contact Email, Phone and Address Details for 5162.1 service in simple two column table format, header then data. For tiled roofs at a slope belowprovide sarking and anti-ponding board at the eaves. AS — Installation of roof tiles. Roof tiles shall be fixed in accordance with the. Metal roofing must be corrosion resistant in accordance with Table 3. Roof tiles shall be fixed in accordance with the BCA and referenced Standard and the nominated design wind speed for the project.

Gutters and downpipes shall be designed and installed in. Timber battens shall 1562.11 sized and installed in accordance. For slab on ground, use damp-proof.

  BF422 TRANSISTOR DATASHEET PDF

AS – Standards Australia

AS — Roof tiles. The homeowner is advised that gutters will require. Advice should be obtained from the manufacturer on the use of metal battens in high corrosive areas. Extend sarking over the bead of valley gutters and turn up neatly along valley. The frame is to be assembled with fixings as per the. Steel framing will comply with Part 3. Code of Practice A code of practice is a set of rules which details how people in a certain industry should aas.

15621 Protection The steel frame must be protected from corrosion in accordance with 3. Roof battens may be of timber or steel. Where battens are joined. Sarking shall be provided for all roofs where the design. Where a gutter discharges onto a tile roof through a. Leave 10 tiles at site for future use.

Direct contact with CCA treated timber is to be avoided. Where one section of roof fully discharges onto a lower section, fully sark the lower section. All roof cladding shall comply with. Where a gutter discharges onto a tile roof through a spreader, irrespective of the roof slope, sark aw roof from the point of discharge over a width of mm down to the gutter.

It specifies requirements for the design and installation of all classes of self-supporting sheet metal roof and wall cladding for both cyclone and non-cyclone regions. Direct contact with CCA treated timber. NASH — Residential and low-rise steel framing —.

  CHOPIN RAINDROPS PDF

Standards Catalogue

Please consult the responsible agency for more information and to ascertain the level of compliance if any that may be required by your business. Secure sarking at the top edge of the fascia and dress down 25mm into the gutter. Steel framing shall be designed and constructed to either: Where battens are joined in a run, they shall be butt jointed at the centre of the truss or rafter. Metal battens shall be corrosion resistant and fixed to the. For tiled roofs at a slope belowprovide sarking and.

Where different metals are. Lead flashings must not be used with aluminium or zincalume roofing or rainwater plumbing, or anywhere where water supply is by rainwater storage. Description You will be required to comply with this standard if you are a registered plumber, licensed plumber, or any other person authorised to carry out plumbing work, and you intend to undertake roofing stormwater work.

You will be required to comply with this standard if you are a registered plumber, licensed plumber, or any other person authorised to carry out plumbing work, and you intend to undertake roofing stormwater work.